From minor seepage to full basement flooding, JCB Waterproofing and Construction provides engineered solutions that protect your foundation and your investment.
Four reasons why Lansing homeowners trust us with their most important asset.
We design every interior drainage system from scratch based on your basement's actual water entry points, soil type, and floor elevation -- no one-size-fits-all kits.
We treat every crack, joint, and tie rod penetration as a potential failure point and address each one individually rather than painting over the problem.
Every technician on our crew holds current certification in basement waterproofing systems and participates in ongoing training as products and methods evolve.
Our quotes include the scope of work, materials specified by brand and model, warranty terms, and the payment schedule -- everything you need to compare us fairly.
Most homeowners in Lansing do not realize that a wet basement is not simply a waterproofing problem -- it is a structural warning sign. Hydrostatic pressure that pushes water through walls does not stop pushing when the water is gone. It continues to stress the concrete and masonry, leading to horizontal cracks in block walls, inward bowing of poured walls, and undermining of the footing system. Addressing the symptom without understanding the root cause means spending money on solutions that fail within a few seasons.
Interior drain tile is the most reliable and widely proven basement waterproofing method for existing homes in MI because it manages water that has already entered the wall cavity rather than attempting to stop it at the exterior. The system consists of a perforated pipe, encased in clean washed gravel, installed at or below the footing level in a channel cut along the perimeter of the basement floor. Water that enters the wall-floor joint, seeps through cracks, or migrates through porous concrete flows into this channel and is directed by gravity to a sump basin. A properly sized sump pump then discharges the water away from the foundation. When correctly installed, this system operates indefinitely without clogging because the inlet is protected from sediment by the gravel bed and a filter sock on the pipe.
In poured concrete walls, the most common seepage points are cold joints, tie rod holes, and form tie locations. These are concentrated, well-defined penetrations that respond well to polyurethane or epoxy injection -- a process of drilling small ports along the crack or joint, installing surface-mounted injection ports, and pumping low-viscosity resin under pressure until it fills the void completely. The cured resin is permanently flexible or rigid depending on the product chosen, creating a watertight seal that moves slightly with seasonal concrete expansion without reopening.
Window wells in below-grade basement windows are a frequently overlooked water entry point. When the well fills with rainwater faster than the soil at the bottom can absorb it, that water presses directly against the window frame -- typically the weakest point in the entire basement envelope. We address window wells with a dedicated drain assembly at the base of the well, tied into the interior perimeter drain system, combined with a properly sized and anchored polycarbonate cover that deflects rain while allowing emergency egress.
A complete basement waterproofing system also requires a reliable, properly maintained sump pump installation. We specify sump pits that are large enough to accommodate both a primary pump and a battery backup pump with sufficient separation that the backup does not interfere with the primary float. Discharge lines are routed to daylight at a point that ensures water flows away from the house and cannot recirculate back to the foundation. Battery backup systems are sized to handle a sustained pumping load during a power outage -- not just a brief test cycle -- because the storm events that knock out power are precisely the events that generate the highest water volume in your basement.
Six core services covering every source of basement moisture in Lansing homes.
We size every drain tile system to the specific hydrology of your basement, ensuring the pipe diameter and sump pump capacity match your worst-case water intrusion load.
Injection ports are removed after cure and the wall surface is patched flush, leaving a clean repair with no visible hardware remaining on the wall face.
Sump pits are sized to accommodate both primary and backup pumps without float interference, and discharge lines are routed to a point at least ten feet from the foundation perimeter.
Hollow-core concrete block walls are treated with hydraulic cement parging and crystalline waterproofing compound that bonds into the block face and eliminates surface seepage.
Basement floor cracks that allow water infiltration from below are treated with polyurethane injection resin pumped under pressure to fill the void and bond with surrounding concrete.
We install polycarbonate well covers sized and anchored to each specific well, deflecting direct rainfall while meeting egress requirements and maintaining ventilation.
Our assessment includes a history review of your water intrusion events and a visual inspection of the exterior grading, gutters, and downspouts that affect subsurface drainage.
Our quotes include alternatives at different investment levels so you can choose a phased approach if budget requires it.
Our certified crew completes the installation with minimum disruption to your home, working from a phased sequence designed to protect furnishings and maintain basement access throughout.
We perform a complete post-installation inspection, take final moisture readings, and walk you through the system before issuing your written warranty documentation.
We had serious standing water every spring for eight years. JCB Waterproofing and Construction installed a full perimeter drain and sump system and we have been completely dry through two wet seasons since.
The quote was detailed, the crew was on time, and the work was exactly as described. They even patched the concrete so neatly you can barely tell there was a drain trench cut.
I called three companies before choosing JCB Waterproofing and Construction. They were the only ones who actually measured the moisture levels and explained what was causing our specific problem before quoting a fix.
Our Lansing waterproofing team is ready for same-day assessments and emergency response. Call now to schedule your free on-site inspection.
Call +1-866-476-1348 Now